just the right temp and some air...
----- Original Message -----
From: Hans S
To: Dr. Champion
Sent: Tuesday, June 29, 2010 12:47 PM
Subject: Help needed for getting resonance
Hello Dr.C
Had my first run the last 4 days with this setup:
Air Temp setting 294 to 297C for getting 291C in Alu pipe ('boat').
Hysteresis set to 1C
After 1 day 295C was needed for getting 291 into the Alu. Stable 291C for 3 days(mass helps...).
Square Alu pipe 10cm length 25cm, 4mm thick. With 16mm Alu base plate. Total mass: 1.4Kg
Tubing covered with alu foil after putting the silver bar in.
Air heating spiral made of 12mm tubing, 6 meters.
Used K type sensors (NiCr-Ni , - 50 to +400 °C) small(3mm)&fast :0.3sec.
Klass 2 deviation: 291Cx0.0075 =+/- 2 C
Sensors 2-3cm into the Alu (holes drilled)
Air pump adjustable from 1 to 9 liters a min. 2 used.
Silver 250gr after 100Hours, no gold formation according to gold tester Mizar M24
Small discoloration of the silver, easy to be wiped away (see middle )
So Dr.C no result so far.
Need more precise sensors? No solid Alu(1.4 kg not enough?)for the ‘boat’? ,
Need to use thin household foil(with enough mass)? Less space between silver and Alu?
Hans
Amsterdam
The Netherlands
His answer:
From: Dr. Champion
To: Dr. Champion
Sent: Tuesday, June 29, 2010 4:25 PM
Subject: My analysis of Hans first test and suggestions.
Everything appears to be totally proper except for the silver resonance. It is obvious that the Al temperature and resonance is working within his kiln. This is obvious from the discoloration of his silver. Allow me to explain this phenomenon. The discoloration occurs from two occurrences’. First there is a slight positive resonance in the reactor with a weak coupling of the resonance to the silver. The coloration of the bar is due to this resonance and the positive air flow, Atmospheric air is ~80% nitrogen and this action on VAu will produce the color. Also remember the resonance coming out of the Al tubing.
Simple practically if the resonance is not directly coupled to the silver a damping effect will occur. This is one of the reasons I have used Al foil because it is not rigid. Now you can use Al foil within a rigid Al container but the Al foil appears to couple to rigid silver more effectively. Hans setup is very professional and all that is required now is a stronger resonance in the bar.
Think of it as a tuning fork and you want to resonate the bar as strongly as possible.
Dr. Champion
Later i tried several diffent setups but no succes...
only my power company is happy with the 1000kWh of experimenting...
have still contact with other unsuccesfull licence members who are still hopefull to receive usefull tech info?!
So, no more response from Dr. C since June 2010?
BeantwoordenVerwijderenWow....
Are you willing to share more info on what was provided. I would like to test it as well.
I saw your other post...Is that the Big Secret he is claiming that is producing him so much gold?
see update (copper to gold).
BeantwoordenVerwijderenthere is a lot more pretending DrC emails to post here...
please post all emails you have from DrC
VerwijderenNo more emails received from DrC...
VerwijderenThank you for your reply , what is the next phase which will require electro digestion , can i have Ted Rey email address ,
Verwijdereni did make gold using yeast and we did test the gold using XRF and the result its pure gold but its only on surface and only 0.5% of gold , so i need to try LENC ,
we tried LENC for 20days for silver to gold , and its looks not surface only its about 40% gold , please take a look on my videos : https://youtu.be/WA7B7Uhh7DA
Verwijderenwhat do you mean by Tubing covered with alu foil after putting the silver bar in.
Verwijderendo you mean we need to put the silver bar inside the alum foil , thanks
Do you have access to his website for 303 group members? drjoechampion303groupmember.com
BeantwoordenVerwijderenBullion Exchanges is a well known Precious Metals Seller established in New York City's Diamond District.
BeantwoordenVerwijderenThey have a wide inventory of products like, metals that range from the ever popular gold and silver to the newly emerging platinum and palladium.
Bullion Exchanges are offering a massive selection of products appealing to 1st time buyers and seasoned investors.
hello
BeantwoordenVerwijderenplz can i have your email i have something important to share with you , we test the gold output from yeast silver process its pure gold but only 0.6% gold , so LENC look better
The YouTube video you provided cannot be viewed. After you removed it from the LENC reactor for 20 days, did you perform annealing or any other heat treatment? Could you please provide detailed instructions?
VerwijderenThank you for the information you provided. I noticed on the Champion's website that after removing it from the 303 reactor, the next step is annealing. Do you have any information about the 'annealing' process?
BeantwoordenVerwijderen